Week 13: Fyp2: Preparation for fyp presentation

Tittle:Preparation for Fyp presentation
Objective: Present the Final Year Project
Content: 1) Make sure project function
         2) Study all technical and theoretical of project

Study on component datasheet:-

Figure 1: About humidity and LM35 sensor

Figure 2: About LDR sensor and controller

Analysis:

Based on this project, student should know what are learning during doing this project. It including the technical and theoretical of component/software used. For my project, I need to know how the sensor, motor pump, cooling fan, lighting and microcontroller specification. For example, I should be know how much current, voltage and watt will produce by the component that used.

Conclusion:
Finally, student should present all of work done to judges. The objective to show what are student had learn around 1 year doing research of project.

Week 12: Fyp2: Design poster for fyp presentation

Tittle: Make a poster for the fyp presentation
Objective: To design a poster about whole project background to make people clearly about the project function
Content: 1)Explain about the project
         2) Clearly the main objective
         3) Design the block diagram
         4) Flow chart about the project from beginning until the end
         5) Make a result and analysis
         6) Conclusion about this project

Introduction of project:-

This system will constantly control and maintain the environment conditions in the greenhouse to ensure that it remains the temperature, light, humidity at the normal level and the plants will always watered two timed per day. It used three sensor which is temperature, humidity and light dependent resistor (LDR) sensor. Three sensor is provide an input signal into a microcontroller which compares these values with the preset values. Depending on the comparison value, the microcontroller will control the operation of a lamp, cooling fan, motor pump to maintain the greenhouse at the normal conditions.

Project Objective:-

1. To design a prototypes of humidity control & automatic greenhouse irrigation system
2. To design and develop humidity and temperature control system
3. To control the amount of water to the plants when it is needed
4. To detect and control the temperature and relative humidity in a greenhouse via microcontroller

Methodology:-

Figure 1: Block system

Result:-

Figure 2: Result taken from project

Poster design:-

Figure 3: Poster project

Analysis:-

From the poster it will describe everything about the project. The assessor can understand about the project from the poster. Block diagram can explain more clearly based on the block show. The block diagram shows the input and the output from the PIC. The result show the way to control the temperature, humidity, lighting and irrigation system. The conclusion is concluding about the whole project.

Conclusion :-

As the conclusion the poster is the most important thing to describe about our project. When the assessor read all the data and information on the poster it will give them satisfaction and just ask when they don’t know certain about the project.

Week 11: Fyp 2: Troubleshoot all part of this project

Tittle: Troubleshoot all part which is temperature sensor, humidity sensor, LDR sensor and motor pump
Objective: To make sure all the circuit is function
Content: 1) Testing the functionality of temperature sensor
         2) Testing the functionality of humidity sensor
         3) Testing the functionality of LDR sensor
         4) Testing the functionality of motor pump

Result:-

Figure 1: Humidity sensor function

The humidity sensor function is to detect the relative humidity in a greenhouse. So, for this project I already choose the chili plants to be experimental. The normal relative humidity for this plants is about 55%-60%. When the humidity sensor detect the wet humidity the cooling fan will be "on" to absorb air. When the humidity sensor detect the normal humidity condition in a greenhouse the cooling fan will be "off".

Figure 2: Temperature sensor function

The temperature sensor function is to detect the temperature in a greenhouse. The normal temperature for plants in a greenhouse is 28 - 29  Celsius. When the temperature sensor detect the high temperature the cooling fan will be "on" to remove air in a greenhouse. When the temperature sensor detect the normal temperature condition in a greenhouse the cooling fan will be "off".

Figure 3: LDR sensor function

Light dependent resistor (LDR) sensor function is detect light. When the sensor is detect no light in a greenhouse the lamp will be "on" while sensor detect light  the lamp will be turn "off".

The motor pump function to water the plants in a greenhouse two times per day there are in the morning and evening. The motor pump will be on and off depends on the setting time on the control panel.


Analysis:-
All the sensor will be programmed to ensure the greenhouse close to the normal condition. The sensor involved in this project are humidity, temperature and light dependent resistor (LDR) sensor. The output for humidity and temperature sensor is cooling fan. It is function to remove and absorb air in a greenhouse. Lamp is the output of LDR sensor and its function to make sure intensity in a greenhouse have a normal condition.

Conclusion :-
As the conclusion, the output of this project only activate depends on the signal from the microcontroller.

Week 10: FYP 2: Conctruct greenhouse prototype

Tittle of project: Construct greenhouse prototype

Objective: To ensure that the greenhouse prototype is built according to the correct dimensions

Content: Construct the greenhouse prototype by using acrylic

Result:-

Figure 1: During construction

Figure 2: After construction

Analysis:-

From the picture above shows the greenhouse prototyping before and after. This project wall and roof is built by using acrylic. The design is basically get from the internet based on the existing product. The wire more important because it can make short circuit, it will damage for this project. The prototype also small, so it is easy to carry and testing the hardware.

Conclusion :
To make some design, we must take note all this aspect such as material that will be used, their costing, product, sizing, item endurance and also their usage. If we miss some of that part, the design will not completely useful.
 

Week 9: FYP 2: Light dependent resistor (LDR) sensor progress

Title of the project: Making and testing the light dependent resistor (LDR) sensor program

Objective: 1) To develop coding of light dependent resistor (LDR) sensor

           2) To ensure the coding can be run properly with the hardware

Content/Procedure:

1) Develop coding for light dependent resistor (LDR) sensor based on the flowchart

2) Testing the coding that can be link with the circuit or not

Result:-

Figure 1: Intensity flow

Analysis:-

The hardware development is suitable matches with the software; it proves when the hardware function, the temperature sensor will detect lighting in a greenhouse. The coding is develop to make sure the sensor will be detect intensity in the greenhouse. The control panel show the current measurement of intensity in a greenhouse. When the intensity  in a greenhouse is less than current measurement the lamp will be "on" to making the plants in a greenhouse be a good condition.

 

Conclusion:-

As a conclusion the result achieve what we expected, and the circuit is function when it matches with the software. The combination of the hardware and software is important to produce the output based on we need.

Week 8: FYP 2: Temperature sensor progress

Title of the project: Making and testing the temperature sensor program
Objective: 1) To develop coding of temperature sensor
           2) To ensure the coding can be run properly with the hardware

Content/Procedure:
           1) Develop coding for temperature sensor based on the flowchart

           2) Testing the coding that can be link with the circuit or not

Result:-

Figure 1: Temperature flow

Analysis:-

The hardware development is suitable matches with the software; it proves when the hardware function, the temperature sensor will measure temperature in the greenhouse. The coding is develop to make sure the sensor will be read the temperature in the greenhouse. The control panel show the current measurement of temperature in a greenhouse. When the temperature  in a greenhouse is bigger than current measurement the cooling fan will be "on" to remove air and making the environment in a greenhouse become normal condition.

 
Conclusion:-

As a conclusion the result achieve what we expected, and the circuit is function when it matches with the software. The combination of the hardware and software is important to produce the output based on we need.

Week 7: FYP 2: Humidity sensor progress

Title of the project: Making and testing the humidity sensor program
Objective: 1) To develop coding of humidity sensor
           2) To ensure the coding can be run properly with the hardware

Content/Procedure:
           1) Develop coding for humidity sensor based on the flowchart

           2) Testing the coding that can be link with the circuit or not

Result:-

Figure 1: Humidity flow

Analysis:-

The hardware development is suitable matches with the software; it proves when the hardware function, the humidity sensor will measure relative humidity in the greenhouse. The coding is develop to make sure the sensor will be read the relative humidity in the greenhouse. The control panel show the current measurement of relative humidity in a greenhouse. When the relative humidity in a greenhouse is bigger than current measurement the cooling fan will be "on" to absorb air and making the environment in a greenhouse become normal condition.

 
Conclusion:-

As a conclusion the result achieve what we expected, and the circuit is function when it matches with the software. The combination of the hardware and software is important to produce the output based on we need.